Welcome to the ozgolf.net forums.
+ Reply to Thread
Page 2 of 4 FirstFirst 1 2 3 4 LastLast
Results 26 to 50 of 79
  1. #26
    Senior Member Multiple Major Winner
    Join Date
    Dec 08, 2011
    Location
    Reaching for my Laser cos I'm a few paces off the green... :)
    Posts
    19,827

    Default

    Lads I have Redtie 7Q3 Reg shaft. It measure 14.5" from the tip to the start of the x on R Flex, how far has it been tipped??

  2. #27
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Bluu, I don't have any data from Matrix on that shaft. Send this guy an email, he is very helpful:

    dsakiyama "at" matrixshafts.com

    Then post back what he says and I'll add it to the list. Maybe grab some black tie and white tie numbers while you at it.

  3. #28
    Senior Member Multiple Major Winner
    Join Date
    Dec 08, 2011
    Location
    Reaching for my Laser cos I'm a few paces off the green... :)
    Posts
    19,827

    Default

    Quote Originally Posted by benno_r View Post
    Bluu, I don't have any data from Matrix on that shaft. Send this guy an email, he is very helpful:

    dsakiyama "at" matrixshafts.com

    Then post back what he says and I'll add it to the list. Maybe grab some black tie and white tie numbers while you at it.
    Thanks mate I will drop him an email

  4. #29
    Senior Member Multiple Major Winner
    Join Date
    Feb 16, 2008
    Location
    QLD
    Posts
    17,085

    Default

    Quote Originally Posted by mrbluu View Post
    Lads I have Redtie 7Q3 Reg shaft. It measure 14.5" from the tip to the start of the x on R Flex, how far has it been tipped??
    I don't have it as 100% beyond doubt yet but i think it is 1".
    WITB
    TRS2 9* Velocore Blue 7s
    G430 9* Ventus Velo 7s
    Titleist TSI2 15* DI7s

    Ping G425 19* hybrid Accra TZ6
    Tour Edge XCG 24* hybrid Altus
    Srixon ZX5 MKII 6-pw
    Ping Stealth 2.0 50*SS, 54*SS, 58SS/TS*
    TP Mills Tour Fleetwood

  5. #30
    Senior Member Multiple Major Winner
    Join Date
    Dec 08, 2011
    Location
    Reaching for my Laser cos I'm a few paces off the green... :)
    Posts
    19,827

    Default

    Quote Originally Posted by TheNuclearOne View Post
    I don't have it as 100% beyond doubt yet but i think it is 1".
    If that the case then it would be perfect.

    Thanks.

  6. #31
    Senior Member Multiple Major Winner
    Join Date
    Dec 08, 2011
    Location
    Reaching for my Laser cos I'm a few paces off the green... :)
    Posts
    19,827

    Default

    Quote Originally Posted by benno_r View Post
    Bluu, I don't have any data from Matrix on that shaft. Send this guy an email, he is very helpful:

    dsakiyama "at" matrixshafts.com

    Then post back what he says and I'll add it to the list. Maybe grab some black tie and white tie numbers while you at it.
    Hey Benno here is the reply from the guy. Please update the OP.

    No problem it looks like it has been tipped 1” here are the measurements for the following from X in Flex:

    7Q3 R Flex – 15 ½”

    7X3 R Flex – 16 ¼”

    7M3 R flex – 20 ½”

    Cheers

  7. #32
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Quote Originally Posted by HatchmanSS76 View Post
    As promised.
    This one doesn't have an easy spot to meassure to so have included pic to help.

    Quadra Fire Express_TP-V 65 SR
    23 1/2" to the start of the C in composite and Quadra Logo which are on the same level (photo angle)
    Quote Originally Posted by mrbluu View Post
    Hey Benno here is the reply from the guy. Please update the OP.

    No problem it looks like it has been tipped 1” here are the measurements for the following from X in Flex:

    7Q3 R Flex – 15 ½”

    7X3 R Flex – 16 ¼”

    7M3 R flex – 20 ½”

    Cheers
    Thanks lads, OP updated.

  8. #33
    Senior Member Multiple Major Winner
    Join Date
    Nov 01, 2008
    Location
    Redlands, on the shores of Moreton Bay
    Posts
    19,214

    Default

    Quote Originally Posted by Daves View Post
    24.75"seems to be the go Graphite Design ADs in stiff;

    AD DI 7S - 24.75" to first green ring
    AD BB 6S - 24.75" to first blue ring

    I am guessing via comparison that X Flex are an inch shorter to the first ring.

    Miyazaki c Kua Tour 43X - 28" to front of M.
    Doing some comparison of tipping on some GD shafts with PeteyD this arvo, seems to confirm the above. An AD DI 6X is an inch shorter to the first green ring than a 6S, so a 6S tipped an inch (to give X flex equivalent) will have rings aligning to 6X out of the factory. The shaft in question was tipped half an inch, which is 3 wood tipping spec.

    Also checked an AD GT 7S, an ADDJ 6S, an ADDI 7S, and 7X, and all conform to the 24.75" to first green ring measurement principle.

  9. #34
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Quote Originally Posted by Daves View Post
    Doing some comparison of tipping on some GD shafts with PeteyD this arvo, seems to confirm the above. An AD DI 6X is an inch shorter to the first green ring than a 6S, so a 6S tipped an inch (to give X flex equivalent) will have rings aligning to 6X out of the factory. The shaft in question was tipped half an inch, which is 3 wood tipping spec.

    Also checked an AD GT 7S, an ADDJ 6S, an ADDI 7S, and 7X, and all conform to the 24.75" to first green ring measurement principle.
    Interesting results on the DI-6X.

    OP updated, thanks Dave!

  10. #35
    Member Touring Pro (Von Nida Tour)
    Join Date
    Jun 11, 2012
    Location
    sydney
    Posts
    631

    Default

    Ad di 6s 24.75 " first green ring
    Last edited by Golfwhang; 9th October 2014 at 09:40 AM.

  11. #36
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Quote Originally Posted by Golfwhang View Post
    Ad di 6s 27.75 " first green ring
    Wow, that's a massive outlier - that sounds a bit "suss".

    Got any history on the shaft?

  12. #37
    Member Touring Pro (Von Nida Tour)
    Join Date
    Jun 11, 2012
    Location
    sydney
    Posts
    631

    Default

    Quote Originally Posted by benno_r View Post
    Wow, that's a massive outlier - that sounds a bit "suss".Got any history on the shaft?
    Sorry benno should be 24.75

  13. #38
    Senior Member Touring Pro (Japanese Tour)
    Join Date
    May 08, 2008
    Location
    Adelaide
    Posts
    1,219

    Default

    Anyone know the measurements for the black DI7s? The graphics don't align like the BB, GT and MT do!

  14. #39

    Default

    I need tip to graphics for a Diamana Redboard 83x5ct. Checking online suggests 18 7/8" to the N in Rayon, however a couple of sites say its over 20".

    I emailed MRC 2 days ago with no response.

  15. #40

    Default

    Just heard back from MRC.

    Redboard 18.75"
    Blueboard 20.75"

    to the N in Rayon. This is for the original series shafts.

  16. #41
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Quote Originally Posted by backintheswing View Post
    Just heard back from MRC.

    Redboard 18.75"
    Blueboard 20.75"

    to the N in Rayon. This is for the original series shafts.
    Thanks Mate, Updates made.

  17. #42

    Default

    Diamana D+ 72x5ct. does anyone have a measurement to the N in RAYON? I will email MRC anyway to double-check.

  18. #43

    Default

    Benno, MRC state 19 5/8" for a Diamana D+ 72 x5ct.


  19. #44
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Quote Originally Posted by backintheswing View Post
    Benno, MRC state 19 5/8" for a Diamana D+ 72 x5ct.
    That's to the the "n" in rayon?

  20. #45

    Default

    Quote Originally Posted by benno_r View Post
    That's to the the "n" in rayon?
    Yes sir.


  21. #46
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Quote Originally Posted by backintheswing View Post
    Yes sir.
    Updated squire.

  22. #47
    Senior Member Touring Pro (Japanese Tour)
    Join Date
    May 08, 2008
    Location
    Adelaide
    Posts
    1,219

    Default

    Quote Originally Posted by talbo View Post
    Anyone know the measurements for the black DI7s? The graphics don't align like the BB, GT and MT do!
    Sent an email to GD, the Black AD DI is 25.75" to first ring.

  23. #48

    Default

    Can this be stickied?


  24. #49
    Senior Member Major Winner
    Join Date
    Mar 04, 2013
    Location
    Maryborough QLD
    Posts
    10,280

    Default

    Sticky now applied, and a few shafts added.

  25. #50
    Senior Member Touring Pro (European Tour)
    Join Date
    May 18, 2013
    Posts
    3,803

    Default

    Quote Originally Posted by Daves View Post
    24.75"seems to be the go Graphite Design ADs in stiff;AD DI 7S - 24.75" to first green ringAD BB 6S - 24.75" to first blue ringI am guessing via comparison that X Flex are an inch shorter to the first ring.Miyazaki c Kua Tour 43X - 28" to front of M.
    What about the tour ad Di hybrid shafts?


 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Similar Threads

  1. .355 taper tip measurements
    By RobNewy in forum Equip Me
    Replies: 13
    Last Post: 23rd February 2012, 07:44 PM
  2. Replies: 3
    Last Post: 22nd January 2012, 08:14 PM
  3. Shaft trimming
    By chappy1970 in forum Equip Me
    Replies: 7
    Last Post: 3rd August 2010, 02:29 PM
  4. Shaft tip trimming help
    By goonie in forum Equip Me
    Replies: 8
    Last Post: 6th April 2009, 04:27 PM
  5. Trimming a putter shaft
    By Bruce in forum Equip Me
    Replies: 12
    Last Post: 19th April 2007, 01:17 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Back to top