PDA

View Full Version : Fully Custom Putter?


andylo
11th April 2007, 03:39 PM
http://www.mibunnputters.com.au/

I am trying to contact this guy but then again I am not too keen about the material they use. Timber.... sounds like the shape of putter would change according to the moisture in the air.

What I am after is a COMPLETE putter customization service, which locate ANYWHERE in Australia. (Seriously, if there's one in Hobart and I will fly to there on Sunday!) Perferrable made with metal material and able to craft it to ANY lie/loft/length. I did some extensive search last hour and the guy above is all I can find.

Hopefully someone can shed some light.
Moe Norman
11th April 2007, 03:56 PM
Scotty Cameron Studio - USA
3oneday
11th April 2007, 04:14 PM
www.slightergolf.com
Jono
11th April 2007, 07:43 PM
www.slightergolf.com (http://www.slightergolf.com)

Mmmm ... The Redmond ...

Nice. 8)
3oneday
11th April 2007, 07:45 PM
hmmm...... the price......

Ugly :p

:lol:
just
11th April 2007, 07:51 PM
I've heard around the US$400 mark! I've had my eye on the Portland or the Olympia. V.nice.
AndyP
11th April 2007, 07:54 PM
Sweet! ;)
http://www.fiveholeputters.com/prod_4_byo_lessHT.htm
PeteyD
11th April 2007, 07:56 PM
Wonder if they would make one with WANKER on the shaft?
3oneday
11th April 2007, 08:31 PM
I've heard around the US$400 mark! I've had my eye on the Portland or the Olympia. V.nice.I got a quote once, and that was as cheap as I could go down to.... Once in a lifetime I suppose but if you can't putt... well, you can't putt !!!

:lol:
just
11th April 2007, 08:33 PM
and I can't putt!!!
markTHEblake
11th April 2007, 09:07 PM
http://www.mibunnputters.com.au/

sounds like the shape of putter would change according to the moisture in the air.

Not a problem Andy

there was a time when all golf clubs were made of wood, and it wasnt untli 1990-ish that wooden clubs really started to become obseleted.
kwantfm
11th April 2007, 10:23 PM
http://www.bettinardi.com/

This is where the action is!
FijiPhil
25th May 2007, 12:58 PM
www.rifeputters.com (http://www.rifeputters.com)

these guys have a bending tool for all their putters so you can change the lie. Also has removable weights on the two bar. Their putters can be completely customised by you.
Davemason
28th May 2007, 11:55 AM
http://www.mibunnputters.com.au/

I am trying to contact this guy but then again I am not too keen about the material they use. Timber.... sounds like the shape of putter would change according to the moisture in the air.

What I am after is a COMPLETE putter customization service, which locate ANYWHERE in Australia. (Seriously, if there's one in Hobart and I will fly to there on Sunday!) Perferrable made with metal material and able to craft it to ANY lie/loft/length. I did some extensive search last hour and the guy above is all I can find.

Hopefully someone can shed some light.

Mate what h/cap are you off (17) :roll:

I think you would be better off spending money on lessons and not on custom putters to get your h/cap down , but then again I've seen you putting stance.
Bit if you want to blow some money off I can get the boys in out fitting & turning shop to bash something up for you at a price :lol:
Fishman Dan
28th May 2007, 12:19 PM
Mate what h/cap are you off (17) :roll:

I think you would be better off spending money on lessons and not on custom putters to get your h/cap down , but then again I've seen you putting stance.
Bit if you want to blow some money off I can get the boys in out fitting & turning shop to bash something up for you at a price :lol:

Uh oh! Troublemaker in our midst!! :smt038