Air compressor for grip install/pull

[Deester]

G'day.

Thinking of getting an air compressor purely for grip install/pulling.

Looking for suggestions for the cheapest and smallest suitable air compressor ... Really don't think I'll have any other use aside of grips for it.

Did a forum search and found a thread or two, but all the links to viable options where either broken or dead.

I have no idea on pressure/psi rating needed etc ... So any links or suggestions for cheap/small compressors would be very welcome ... Thinking it's likely a Bunnings purchase or the like ?

Thanks in advance.

[Dotty]

Ryobi One+ 18v Inflator/Deflator has worked well for me over the last 4 years (especially since it is compatible with my handyman and garden care tools, including a tiny lawnmower for 120sqm of lawn).

10psi is default and good for putting on grips. Generally, use 30psi for removing grips (wrapped in a tea towel) and can crank it higher for tougher jobs.

[pt73]

This one is similar to what I bought ages ago and comes with an accessory kit.

https://www.bunnings.com.au/ozito-21l-1-5hp-oil-free-air-compressor-kit_p0283490

This one is cheaper and smaller.

https://www.bunnings.com.au/ozito-6l-1-5hp-air-compressor-kit_p0048827

[virge666]

Anything on FB market place will do it.
use the paint spray adapter to jam in the back of the grip. Been only using air since the 90's

if you are nervous.. get some arty spray adhesive that doesn't immediately set.

https://www.facebook.com/marketplace/item/729737765125629/?ref=search&referral_code=marketplace_search&referral_story_type=post&tracking=browse_serp%3A201a8f96-f2ce-4a69-a924-271b894a54b4

[Deester]

Thanks for the info gents ... Exactly what I was after.

[markTHEblake]

Ryobi One+ 18v Inflator/Deflator has worked well for me over the last 4 years Is this an April Fools joke? :-)

I have no idea but just astounded this type of unit can push out enough air? I had looked at small units like this before but figured that aside from pumping tyres they are useless for anything else.

[Dotty]

Is this an April Fools joke? :-)

I have no idea but just astounded this type of unit can push out enough air? I had looked at small units like this before but figured that aside from pumping tyres they are useless for anything else.
It's great for grips and tyres, especially when picking up trailers that haven't been checked for a while. (May also minimise grip ballooning, due to slower pressure build-up.)

Useless for blowing dirt/grass/sawdust from the ute tray/garage/deck (but the leaf blower using the same battery does the job well).

No idea how effective it is for airbeds, using the high-volume/low-pressure setting.

[backintheswing]

I have a Makita 18v one dotty. Perfect for grips, MTB tyres and inflatable pools
https://www.totaltools.com.au/179443-makita-18v-inflator-skin-dmp181z

[BobsYourUncle]

Ryobi One+ 18v Inflator/Deflator has worked well for me over the last 4 years (especially since it is compatible with my handyman and garden care tools, including a tiny lawnmower for 120sqm of lawn).

10psi is default and good for putting on grips. Generally, use 30psi for removing grips (wrapped in a tea towel) and can crank it higher for tougher jobs.

this one? https://www.bunnings.com.au/ryobi-one-18v-cordless-air-inflator-and-deflator-tool-only_p6210400

[Dotty]

this one? https://www.bunnings.com.au/ryobi-one-18v-cordless-air-inflator-and-deflator-tool-only_p6210400
That's the one.

I use an after-market ribbed brass nozzle for the grips, but it comes with a plastic nozzle that would suffice.

[LeftyHoges]

I have one of these (or the couple of years old equivalent now), works great....

https://www.bunnings.com.au/ozito-1100w-inflate-it-compressor-kit_p6290649

[Matt 3 Jab]

I have one of these (or the couple of years old equivalent now), works great....

https://www.bunnings.com.au/ozito-1100w-inflate-it-compressor-kit_p6290649Yeah I've got this one. Grips on is fine, not ideal for stuck grips and blowing them off but can be done in the right situation.

Great for the other odd jobs around house like tyres and pools

[spanner039]

Yeah I've got this one. Grips on is fine, not ideal for stuck grips and blowing them off but can be done in the right situation.Great for the other odd jobs around house like tyres and poolsAnother vote for that one That’s the one I’ve got as well

[perci]

.

[Froggy]

Sort of on topic.....any suggestions to stop grips bubbling and going way out of shape when removing with air ?.........I've never really had much luck :)
Thanks

[Daves]

Sort of on topic.....any suggestions to stop grips bubbling and going way out of shape when removing with air ?.........I've never really had much luck :)ThanksWon't stop bubbling, but can reduce damage by using a piece of poly pipe or similar over the grip when removing. Even the cardboard roll from Alfoil/ Gladwrap will work in a pinch.

[Froggy]

Thanks Daves

[Dotty]

Fold a tea towel in thirds and wrap it tightly around the grip. (Optionally, wrap some masking tape around this in three or four places to hold it, until you get the confidence.)

If you have the option, start with a low pressure (10-20psi) and twist the grip to let the air gradually break the adhesion (which is easier with a tea towel than PVC pipe). If you feel the grip starting to blister, quickly knock the valve from the grip and reassess your strategy, like applying hand pressure, where it tried to blister.

[Daves]

Sort of on topic.....any suggestions to stop grips bubbling and going way out of shape when removing with air ?.........I've never really had much luck :)
Thanks


Won't stop bubbling, but can reduce damage by using a piece of poly pipe or similar over the grip when removing. Even the cardboard roll from Alfoil/ Gladwrap will work in a pinch.


Fold a tea towel in thirds and wrap it tightly around the grip. (Optionally, wrap some masking tape around this in three or four places to hold it, until you get the confidence.)

If you have the option, start with a low pressure (10-20psi) and twist the grip to let the air gradually break the adhesion (which is easier with a tea towel than PVC pipe). If you feel the grip starting to blister, quickly knock the valve from the grip and reassess your strategy, like applying hand pressure, where it tried to blister.

Dotty's method works, just take it easy as he said. I have wrapped a towel to do the same.

Before I start, I try to assess how "stuck" the grip is by rolling it up from the bottom, as far I can. If it seems to be well glued (the evil doubled sided paper will be visible!) then I use one of these and some Metho to loosen it up as much as I can;

https://www.golfworks.com/the-golfworks-v-groove-grip-remover/p/vggrv/

I have not tried it but some say a folded wire clothes hanger can be used to do the same.

Others use a needle to inject a Hydrocarbon (Petrol, White Spirit, Metho etc) under the grip to loosen the glue first. Which is sort of the reverse of how doubled sided paper grips are installed, traditionally.

[Froggy]

All very helpful info....cheers

[pt73]

Dotty's method works, just take it easy as he said. I have wrapped a towel to do the same.

Before I start, I try to assess how "stuck" the grip is by rolling it up from the bottom, as far I can. If it seems to be well glued (the evil doubled sided paper will be visible!) then I use one of these and some Metho to loosen it up as much as I can;

https://www.golfworks.com/the-golfworks-v-groove-grip-remover/p/vggrv/

I have not tried it but some say a folded wire clothes hanger can be used to do the same.

Others use a needle to inject a Hydrocarbon (Petrol, White Spirit, Metho etc) under the grip to loosen the glue first. Which is sort of the reverse of how doubled sided paper grips are installed, traditionally.
If the grip was installed with double sided tape, I squirt some turps into the shaft though the hole in the grip butt and put some pvc pipe over the grip and gently apply some pressure.

Some of the really thin OEM grips just bubble up but I would save at least 90% of grips using this method.

I just wrap a cloth over the shaft near the bottom of the grip to soak up any turps that spurts out.

It works a treat with Superstroke putter grips even though the pvc pipe doesn’t fit over some sizes.

[Johnny Canuck]

If the grip was installed with double sided tape, I squirt some turps into the shaft though the hole in the grip butt and put some pvc pipe over the grip and gently apply some pressure.

Some of the really thin OEM grips just bubble up but I would save at least 90% of grips using this method.

I just wrap a cloth over the shaft near the bottom of the grip to soak up any turps that spurts out.

It works a treat with Superstroke putter grips even though the pvc pipe doesn’t fit over some sizes.

I’m going to try the metho in the shaft method next time. I used a heat gun on the grip to warm up the double sided tape the other day and it worked a treat.

[keymaster]

The other thing I've started to do. When I don't know if there's double sided tape. Similar to the coat hanger method, I'll use a long flat bbq skewer with some metho and force it down the grip. 99.9% breaks off the tape and then the grip won't burst or bubble from there.

Other method which is a bit slower, heat gun over the grip. But it takes longer and I find there's still a decent chance of bubbles.

[pt73]

I’m going to try the metho in the shaft method next time. I used a heat gun on the grip to warm up the double sided tape the other day and it worked a treat.
I've always used turps as it doesn't dry too quickly and is more "slippery".

[Timbo]

I use a section of lay flat hose about 30cm long. It does the same as the pvc/poly, but allows you to grip & twist like the tea towel method.

[Hatchman]

Just a few questions on the use of Turps v Metho with those that have used to remove well stuck grips?
Do you try to salvage these grips for re-use?
Doesn't Turps leave an oily residue behind that makes it harder to clean up/salvage the grip for reuse?

[Captain Nemo]

White spirts
https://www.bunnings.com.au/diggers-1l-white-spirit_p1563471

[pt73]

Just a few questions on the use of Turps v Metho with those that have used to remove well stuck grips?
Do you try to salvage these grips for re-use?
Doesn't Turps leave an oily residue behind that makes it harder to clean up/salvage the grip for reuse?
Yes I save them for reuse and turps dries pretty quickly.

In most cases this method leaves the grip tape attached to the shaft.

Once removed I put the grips vertically (butt down) on some newspaper so any excess turps drains out the hole in the grip butt.

The only other thing that needs to be done is to put the clubs (I.e. an iron set) in a drip tray with the head pointing upwards to let an excess turps drain out.

If it’s a single club then I do the same but with the club clamped in a vice with the shaft butt pointing down into a drip tray or old can.