View Full Version : Found: Steelfiber 110cw / recoil 110 / matrix program 130
benno_r
6th March 2015, 08:52 PM
Bit of a long shot, but got some beautiful new heads that need some graphite shaft love.
Chasing:
Steelfiber i110reg taper. 4-pw
Steelfiber i110stiff taper 3-9
Recoil 110f4 3-9.
Matrix program 130 5.5 4-pw
Trade bait:
Shimada tour lite 3-pw stiff brand new uncut
C taper lite 3-pw used
(Both not for sale outright)
Cheers,
Ben
mrbluu
6th March 2015, 08:56 PM
Dibs ;-)
D22marshall
7th March 2015, 07:38 AM
Check this item number ebay 291394961734
Not quite enough clubs but good deal
sainters
7th March 2015, 10:36 AM
Hi Ben
I have a set of steelfiber i95's (reg). We may be ableto do a swap for the c-taper lites ???
Let me know if you want to chat ???
Cheers,
Edward
benno_r
7th March 2015, 12:21 PM
Hi Ben
I have a set of steelfiber i95's (reg). We may be ableto do a swap for the c-taper lites ???
Let me know if you want to chat ???
Cheers,
Edward
Hi Edward,
Got some i95reg already in some covert forged, looking for sonething a little heavier.
Cheers,
Ben
tommyg
8th March 2015, 08:29 PM
I've got some matrix program 130s 4-p in j40cb's. Yours for $500pp. Not keen to pull them....
benno_r
8th March 2015, 08:32 PM
I've got some matrix program 130s 4-p in j40cb's. Yours for $500pp. Not keen to pull them....
If I can line up a head buyer, that might work. What flex and length are they mate?
tommyg
8th March 2015, 08:53 PM
Stiff... Play standard length in the Bridgey's
benno_r
8th March 2015, 08:55 PM
Stiff... Play standard length in the Bridgey's
Ok mate, let me look into it.
benno_r
13th March 2015, 09:10 AM
Stiff... Play standard length in the Bridgey's
Not sure I could move the heads, and would need to buy a 4i shaft after I soft stepped these to get length, so I'll pass mate.
Cheers,
Ben
benno_r
13th March 2015, 09:11 AM
OK, tradebaits off the table.
One last bump before I go back to stinky old steel. Slight change in what I am chasing:
Steelfiber i110reg taper. 4-pw
Recoil 110f4 3-pw.
Matrix program 130 stiff 3-pw
Cheers,
Ben
benno_r
13th March 2015, 10:39 PM
Shafts incoming, you know what to do megamods.
D22marshall
14th March 2015, 07:17 AM
Gaz?
benno_r
14th March 2015, 07:23 AM
Gaz?
Nah, got some programs. He had some pulls, but only in parallels.
D22marshall
14th March 2015, 07:25 AM
Well done
benno_r
4th April 2015, 10:32 PM
I've got some matrix program 130s 4-p in j40cb's. Yours for $500pp. Not keen to pull them....
Hey Tom, can you clear up some PM space?
Cheers,
Ben
Powered by vBulletin® Version 4.1.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.